# Note: skips lists for CI are just a list of lines that, when
# non-zero-length and not starting with '#', will regex match to
# delete lines from the test list.  Be careful.

# This test checks the driver's reported conformance version against the
# version of the CTS we're running. This check fails every few months
# and everyone has to go and bump the number in every driver.
# Running this check only makes sense while preparing a conformance
# submission, so skip it in the regular CI.
dEQP-VK.api.driver_properties.conformance_version

# Exclude this test which might fail when a new extension is implemented.
dEQP-VK.info.device_extensions

# These are tremendously slow (pushing toward a minute), and aren't
# reliable to be run in parallel with other tests due to CPU-side timing.
dEQP-GLES[0-9]*.functional.flush_finish.*

# piglit: WGL is Windows-only
wgl@.*

# These are sensitive to CPU timing, and would need to be run in isolation
# on the system rather than in parallel with other tests.
glx@glx_arb_sync_control@timing.*

# This test is not built with waffle, while we do build tests with waffle
spec@!opengl 1.1@windowoverlap

# These tests all read from the front buffer after a swap.  Given that we
# run piglit tests in parallel in Mesa CI, and don't have a compositor
# running, the frontbuffer reads may end up with undefined results from
# windows overlapping us.
#
# Piglit does mark these tests as not to be run in parallel, but deqp-runner
# doesn't respect that.  We need to extend deqp-runner to allow some tests to be
# marked as single-threaded and run after the rayon loop if we want to support
# them.
#
# Note that "glx-" tests don't appear in x11-skips.txt because they can be
# run even if PIGLIT_PLATFORM=gbm (for example)
glx@glx-copy-sub-buffer.*

# These test the loader more than the implementation and are broken because the
# Vulkan loader in Debian is too old
dEQP-VK.api.get_device_proc_addr.non_enabled
dEQP-VK.api.version_check.unavailable_entry_points

# These tests are flaking too much recently on almost all drivers, so better skip them until the cause is identified
spec@arb_program_interface_query@arb_program_interface_query-getprogramresourceindex
spec@arb_program_interface_query@arb_program_interface_query-getprogramresourceindex@'vs_input2[1][0]' on GL_PROGRAM_INPUT

# These tests attempt to read from the front buffer after a swap. They are skipped
# on both X11 and gbm, but for different reasons:
#
# On X11: Given that we run piglit tests in parallel in Mesa CI, and don't have a
# compositor running, the frontbuffer reads may end up with undefined results from
# windows overlapping us.
# Piglit does mark these tests as not to be run in parallel, but deqp-runner
# doesn't respect that.  We need to extend deqp-runner to allow some tests to be
# marked as single-threaded and run after the rayon loop if we want to support
# them.
# Other front-buffer access tests like fbo-sys-blit, fbo-sys-sub-blit, or
# fcc-front-buffer-distraction don't appear here, because the DRI3 fake-front
# handling should be holding the pixels drawn by the test even if we happen to fail
# GL's window system pixel occlusion test.
# Note that glx skips don't appear here, they're in all-skips.txt (in case someone
# sets PIGLIT_PLATFORM=gbm to mostly use gbm, but still has an X server running).
#
# On gbm: gbm does not support reading the front buffer after a swapbuffers, and
# that's intentional. Don't bother running these tests when PIGLIT_PLATFORM=gbm.
# Note that this doesn't include tests like fbo-sys-blit, which draw/read front
# but don't swap.
spec@!opengl 1.0@gl-1.0-swapbuffers-behavior
spec@!opengl 1.1@read-front

# Skip test everywhere
# Because even with a 256x256 map, it is over 1 GiB of texture memory
# allocated
# Also, individually, it was disabled in most of the tests as it is
# either too slow or results in an OOM
spec@!opengl 1.1@streaming-texture-leak